User’s Manual IP Telephony Gateway Model No.: SP5050 / SP5052 / SP5054 http://www.micronet.info Version 2.0
2.3 Network configurations in your Gateway 1. Key in the IP address of the Gateway (http://10.1.1.3) with the browser 2. After key in the IP add
3. You will enter the main page of the configuration after key in the login name and password correctly: Figure 4. The main web page 4. Press the Ne
2.3.1 Static IP address 1. Please get the correct IP address, Netmask and default Gateway address from your ISP first. Press the OK button if you f
3. Press the reboot if you want the configuration executed. Figure 8. Reboot the system 2.3.2 DHCP mode 1. Enable the DHCP if you are using the c
2. Please commit the data and reboot the machine after you enable the DHCP function. 2.3.3 PPPoE mode 1. Press the PPPoE Configuration and put th
3. Making a VoIP Call There are two modes that you could configure the Gateway for making VoIP calls. One is the Peer-to-Peer mode, another is GK ro
3. Enter the Phone Book configuration table and configure the name, IP address and phone number of the destination. Figure 12. Phone Book 【Example
This is the first record of Phone Book. So the index is 1 The name of the destination: test The E164 number (phone number) of the destination: 123 Th
3.2 Configure the Gateway into the GK routed mode 1. Enter the H323 Configuration table and change the mode from Peer-to-Peer to GK routed. To chan
183. Press the Commit Data and Reboot System buttons when you finished the configuration. There are two types in the GK routed mode you could cho
Table of Contents 1. INTRODUCTION ...2 1.1 Features and specific
4. Command List 4.1 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure Gateway. There are kinds of terminal em
2. Define a name such as ‘SP5050’ for this new connection. Figure 18. Edit the name of the connection 3. After pressing OK button, the next windo
4. Configure the COM Port Properties as following: Bits per second: 9600 Flow control: None Figure 20. COM properties 5. Press ‘OK’ button,
224.2 Command List 4.2.1 [help] command Type help or man or ? to list all the available command. usr/config$ ? help help/man/? [command] quit
23And turn back to login prompt. usr/config$ quit Disconnecting... login: Note: It is recommended that type the “quit” command before you leave
24AC4804[2] is OK Successful Initialize OSS libraries...OK! open stack successful cmInitialize succeed! GK mode selected. login: 4.2.5 [flash]
254.2.7 [ifaddr] command Configure and display Micronet FXO Gateway network information. usr/config$ ifaddr LAN information and configuration
26Parameters Usage: -print print current IP setting -ip assigned IP address for Micronet FXO Gateway -mask internet subnet mask -gate IP defaul
27IP-Sharing, user can enable IP sharing function and specify public IP address of IP-sharing. 4.2.8 [time] command When SNTP function of Micron
28disconnect tone. If Micronet FXO Gateway can’t hang up call and release line correctly, please use this function to analyze disconnect tone of PS
21. Introduction Micronet SP5050 series VoIP FXO Gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your
292. Disconnect Tone Analysis : please follow instructions on screen ; first call in line1 of Micronet FXO Gateway from PSTN side(now can’t hear g
303. exit : exit this command usr/config$ greetrd ================================================== Welcome to Voice Record/Analysis Mode
31 -delete Delete a record from Phonebook. -insert Insert a record to Phonebook in specified position. -modify Modify an exist
32number for it. -modify modify an existing record. When using this command, users have to specify the record’s index number, and then make the ch
33number plan very well to avoid the numbering conflict. If users already defined “0” for specific trunk Gateway, other terminal started with “0” s
344.2.12 [pppoe] Display PPPoE related information. PPPoE device information and configuration Usage: pppoe [-print]|[-open]|[-close] pppoe [-de
354.2.13 [ddns] command This command supports the DDNS function. usr/config$ ddns The dynamic DNS service information and configuration Usag
36Parameter Usages: -enable enable the DDNS function -server enter the server address of the DDNS server you use -hostname enter the domain name
37 -ringdet Specify Gateway ring detect method. (0:For 1st hardware version, 1:For 2st hardware version. -plan Number
38 sysconf -2nddial 0 -drule out_filter 002 in_insert x in_drop 1 sysconf -askpin 1 -pincode set1 12345 usr/config$ Parameter U
3y Support static IP and DHCP y Provide QoS function by ToS (Type Of Service) setting y Provide T.38/FAX and voice Auto-Switching y Microsoft
39button, 2:[#]button ) - seizure line seizure mode. None (0) Æ when calling from IP side, choose L1 every time if it is available. UCD (1) Æ when
40-askpin: 0Æ disables ASKPIN function 1Æ enables ASKPIN function, and apply to the whole unit. Every channel uses the same PINCODE. 2Æ enables AS
41H.323 stack information and configuration Usage: h323 h323 [-gk ipaddress] [-multicast used] [-e164 number] [-alias h323id] [-rtp port] [-h2
42-print print current h323 related settings -mode alternatives for gatekeeper or peer-to-peer mode (0=gatekeeper mode; 1=peer-to-peer mode). I
43press 101 or 102 dialing to line1 or line2 of Micronet SP5052 after hearing greeting of Micronet FXO Gateway. -e164 e164 number, which is re
44new call (1~200). -connto connection timeout. Max waiting time for call establishment after receiving 1st response of a new call (1~20000). 4.
45 input gain (0~63, default: 32), dtmf volume (0~31, default: 27), -nscng No sound compression and CNG. (G.7
46 -mindelay the minimum jitter buffer size. (Default value= 90 ms) -maxdelay the minimum jitter buffer size. (Default value= 150 ms) usr/config$
47devices (for ex: router, switch.. etc.) support ToS. 2. tos -rtptype 14 -sigtype 10 is top priority of package. 4.2.18 [tone] command Tone d
48 -t38 T.38(FAX) enabled/disabled. -t38ecm T.38(FAX) ECM enabled/disabled. -fstart Fast start enabled/disabled. -tunnel H245 T
1.3 Appearance Front Panel: Here is an example for SP5050. Power: Light on means Micronet SP5050 is power on. L1-L6: Light on means the line is i
49incompatibility with other devices. 2. If user wants to use T.38 fax under fast start mode, please make sure “h245fs” function is enabled, or fa
50Parameter Usages: - print display current grouping information - enable enable grouping function - disable disable grouping function - number
51 $sysconf -service 2 (HotLine service) $sysconf -2nddial 0 (2nddial off) $h323 -mode 1 (peer-to-peer mode) L
52numbers information. - hotline the same function with table command. 4.2.22 [prefix] command This function can do digits replacement of inc
53 4.2.23 [rom] command ROM file information and firmware upgrade function. usr/config$ rom ROM files updating commands Usage: rom [-app] [-dspt
54Parameter Usages: -print show versions of all rom files -app, boot, dsptest, dspcore, dspapp to update main Application program code, Boot code
55-ftp if users choose FTP in above item, it is necessary to specify pre-defined username and password when upgrading files. 4.2.24 [passwd] com
The pin-out is as following: PIN 1, 2: Transmit PIN 3, 6: Receive COM: RS232 console port (DB-9 male connector) Note: use straightforward cable to
62. Setting Up the TCP/IP Protocol 2.1 System Requirements 1. One PC with: (a) Pentium 100 or above, 64 RAM, Windows 98 or above; (b) Ethern
panel. 2. Enter the network configuration. Figure 1. Network Configuration 3. Select the Property of the LAN card. 4. Setup the IP address, subne
8The default IP address, Netmask and default Gateway address of the Gateway is 10.1.1.3, 255.255.0.0, and 10.1.1.254.
Comentarios a estos manuales