MicroNet SP918GL Manual de usuario

User’s Manual Wireless Access Point Model No.: SP918GL Website:http://www.micronet.info

10 Getting Started A. First, connect the power adapter to the receptor at the back panel of the 54Mbps Access Point and then plug the other end of

11 An Infrastructure wireless network contains an Access Point or Router. The Infrastructure Network example, shown here, contains the following netw

12 Using the Web Configuration Utility The easiest and quickest way to connect to a wireless network using your 54Mbps Access Point is to use the Co

13 There are three other options available in this screen: Setup Wizard, Advanced Setup, and Statistics. Current Status The left-hand side of th

14 Setup Wizard Using the built-in Setup Wizard is the easiest and quickest way to connect to a wireless network. To take advantage of this convenien

15 This screen displays the present level of security on your Access Point. To use encryption, click Enabled, choose the Key Size, and enter the en

16 After rebooting, the sign-in window will reappear. Simply type in admin (or a new user name and password if you have changed them). Advanced

17 For more detailed information, click on Configuration to bring up the following screen with an expanded menu. Click Device Information.

18 WLAN Parameter Settings SSID: (Service Set Identifier): WLAN is the default setting. The SSID is a unique name that identifies a network. All

19 within the value range of 256 to 2346. Setting the Fragment Length too low may result in poor performance. RTS Length: This value should remain at

2 Contents System Requirements For Configuration...3 Introduction...

20 Access Control Settings Control: Disabled - Disable the Access Control feature Accept - Accept the MAC Addresses in the list into the netwo

21 Security Settings Wireless Band: If the access point is an 11g device, IEEE 802.11g will be the only choice here. Authentication: Select from

22 Administration User Name: The default User Name is admin. Old Password: To change your password, first enter the old password. New Password: E

23 Misc Telnet Service: When enabled, Administrator can access the device configuration via Telnet operation. Timeout: Under the Telnet session

24 Maintenance/Update Firmware Update File: Click on Browse to find the new firmware file from your hard drive. After you find the updated firmwa

25 Restart System Apply Settings and Restart: If you have made any changes to the configuration settings, click Restart to apply the changes.

26 Statistics Throughput Displays the WLAN 11g throughput statistics for received, transmitted and RTS communications. Transmitted Displays

27 Received Displays the 11g WLAN Rx Fragment Count, Multicast Rx Frame Count, Rx Frame FCS Error Count, Rx Frame Duplicate Count and Ack Rx Fai

28 Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the 54Mbps Access Point. W

29 2. The computer cannot access the Internet in the Infrastructure mode. Make sure the computer is associated and joined with the correct Access

3 Package Contents • IEEE 802.11g 2.4GHz Wireless LAN Access Point • Power Adapter – 5VDC, 2A • Installation Guide on CD • Straight-through Et

30 3. Check that the drivers for the network adapters are installed properly. You may be using different network adapters than those illustrated h

31 • Double-click on Network Adapters • Right-click on IEEE 802.11g Wireless Cardbus Network Adapter • Select Properties to check tha

32 4. What variables may cause my wireless products to lose reception? Wireless products let you access your network from virtually anywhere you w

33 Technical Specifications Standards  IEEE 802.11g  IEEE 802.11b  IEEE 802.3  IEEE 802.3u Device Management  Web-Based - Internet Explorer

34 Safety and Emissions:  CE Physical Dimensions:  L = 110mm  W = 80mm  H = 20mm Wireless Data Rates with Automatic Fallback:  54 Mbps 4

35 Media Access Control:  CSMA/CA with ACK Wireless Transmit Power:  15dBm(32mW)±2dB Power Adapter:  Ext. Power Supply DC 5V, 2.0A  100V

4 Introduction The 54Mbps Access Point provides the most expanded user bandwidth available in an AP. Network members can connect to this AP using a

5 Connections • Straight-Through cable is required when connecting to a router or switch • Cross-Over cable is required when connecting directly

6 LEDs LED stands for Light-Emitting Diode. The 54Mbps Access Point has 3 Green LEDs as shown below: LED LED Activity Power A steady light indica

7 Wireless Basics The 54Mbps Access Point is based on industry standards to provide easy-to use and compatible high-speed wireless connectivity withi

8  The 54Mbps Access Point is compatible with the IEEE802.11g wireless products: 802.11g Wireless Cardbus Adapters used with laptop computers and

9 Installation Considerations Desktop and laptop computers with wireless network adapters installed can access the 54Mbps Access Point from virtual